802.3af Power-over-Ethernet (PoE) Injector
Place PoE-enabled Access Points and IP Cameras Where You Need Them
EPE-5818af
Fast Ethernet In and Out Ports
IEEE 802.3af (PoE) Compliant
Supports PoE Cabling Up to 300 feet
48V Power to 802.3af Devices over CAT6 Cabling


EPE-5818af 802.3af Power-over-Ethernet (PoE) Injector

Eliminate the limitation of placing an (802.3af) PoE-enabled device, such as a Wireless Access Point or IP Camera near a power outlet. The EPE-5818af delivers both data and electrical power to PoE-enabled devices using a single Ethernet CAT6 cable. EPE-5818af PoE injector is 802.3af compliant, and also features two Fast Ethernet (10/100 Mbps) ports - one port for a connection to an Ethernet switch and the other for connection to a PoE-enabled device.

It uses standard IEEE pin definition to power the device, and comes with a 48V/0.375A power supply. Pin# 1, 2, 3 and 6 for data transmission; pin# 4, 5, 7 and 8 for power to the device. The EPE-5818af PoE generates power over CAT6 cable up to 300 feet (100 meter). By sending 48V, Ethernet terminals such as Wireless LAN Access Points, IP Phones and IP Cameras can be powered more remotely from an Ethernet switch. The PE-5818Gaf is especially useful for outdoor networking deployments and low port density installations.

Made For Harsh Outdoor Environments
Its durable housing is applicable for most indoor and outdoor installations.
Faster File Transfers with Fast Ethernet
Utilizes Fast Ethernet standard speeds of up to 100 Mbps for faster file transfers and video streaming.
Extended Range and Reach
Allows wireless devices to be mounted on the wall, ceiling, or where external power is not readily accessible with cabling up to 300 feet.
IEEE 802.3af (PoE) Compliant
802.3af compliant, and also features two Fast Ethernet (10/100 Mbps) ports - one port for a connection to an Ethernet switch and the other for connection to a PoE-enabled device.
Delivers Data & Power
The injector delivers both data and electrical power to PoE-enabled devices using a single Ethernet CAT6 cable enabling network administrators to connect and power VoIP (Voice-over-IP) phone systems or to mount Wireless Access Points and IP Cameras in ceilings or in crawlspaces or where power outlets may not be available.

Technical Specifications


Standard
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-T


Protocol
CSMA/CD


Ports
data-In
PoE Out
DC Jack


Data Lines
Pair 1: Pin1 (Rx+)/Pin2 (Rx-)
Pair 2: Pin3 (Tx+)/Pin6 (Tx-)
Pair 3: Pin4 (Vdc)/Pin5 (Vdc-)
Pair 4: PIn7 (Vdc-)/Pin8 (Vdc-)


Power Lines
Pair 3: 4/5
Pair 4: 7/8

Diagnostics LED
Power: Green

Power Output
Provides up to 24W
Input: AC100-240 V, 50-60 Hz
Output: DC 48V/0.5A (Maximum Output)


Reliability/MTTF
25000 Hours


 


 


 


 


 


 

Environmental & Physical


Temperature Range
Operating: 32ºF to 140ºF/ 0ºC to 60ºC
Storage: -22ºF to 176ºF/-30ºC to 80ºC

Humidity (non-condensing)
Operating: 5%~90%
Storage: 5%~90%


Maximum data rates are based on IEEE 802.3ab standards. Actual throughput and range may vary depending on distance between devices or traffic and bandwidth load in the network. Features and specifications subject to change without notice. Trademarks and registered trademarks are the property of their respective owners. For United States of America: Copyright ©2014 EnGenius Technologies, Inc. All rights reserved. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense.



Dimensions & Weights


EPE5818af Device
Weight: 0.14 lbs.
Width: 1.81"
Length: 3.23”
Height: 0.83”

Package Contents
EPE-4818G PoE Injector
48V/0.5A Power Adapter
Quick Installation Guide

Warranty
1 Year