EWS850AP是EnGenius首款Wi-Fi 6解決方案的戶外基地台。802.11ax的無線網路標準，採用OFDMA和MU-MIMO技術讓基地台具備高速並可在多種應用上高密度使用。
| 檔案名稱 | 類型 |
|---|---|
 規格手冊_EnGenius EnSky Indoor AP
|
Data Sheet |
|
規格手冊_EnGenius EnSky Outdoor AP
|
Data Sheet |
|
快速安裝指南_EWS850AP
|
Quick Guide |
|
EWS850AP User Manual EN
|
User Manual |
|
EWS850AP FW v3.8.2.1_c1.9.51
|
Firmware |
|
EWS850AP FW v3.8.8_c1.9.51
|
Firmware |
802.11ax and ac/a/b/g/n compliance
SMA Type interfaces
2.4GHz: Two(2) detachable 5.0dBi SMA antennas
5GHz: Two(2) detachable 5.0dBi SMA antennas
Optional Solutions
Alternative solution to compatible with SA2216 and SA5219 sector Antennas
One (1) 10/100/1000 BASE-T RJ-45 Ethernet Ports
4 x SMA Connector Interfaces
Display system and wireless transmission status
Maximum Power Consumption
Power Source
802.3af/at Compliance Source
Proprietary 48V-54V
Active Ethernet (Power Over Ethernet, PoE)
1KV
Contact: 4KV
Air: 8KV
Pole Mount
Wall Mount
Outdoor, IP67, dual radios concurrent, 5GHz 802.11ax 2×2 MU-MIMO is backwards compatible with 802.11 ac/a/n mode, 2.4GHz 802.11 ax 2×2 MU-MIMO is backwards compatible with 802.11 b/g/n.
Two(2) spatial streams SU-MIMO for 2.4GHz and two(2) spatial streams SU-MIMO for 5GHz up to totally 1,774Mbps wireless data rate to a single 11ax wireless client device under the both 2.4GHz and 5GHz radio.
Two(2) spatial streams multi-user (MU)-MIMO for up to 1201 Mbps wire-less data rate to transmit to one(1) two streams MU-MIMO 11ax capable wireless client devices under 5GHz simultaneously.
Two(2) spatial streams multi-user (MU)-MIMO for up to 574 Mbps wireless data rate to transmit to one(1) two streams MU-MIMO 11ax capable wireless client devices under 2.4GHz simultaneously.
2.4GHz: 2400MHz ~ 2482MHz
5GHz: 5150MHz~5250MHz, 5250MHz~5350MHz, 5470~5725MHz, 5725MHz~5850MHz
Support radios and channels will be varied on the configured regulatory domain.
802.11ax: Orthogonal Frequency Division Multiple Access (OFDMA)
802.11b: Direct-sequence spread-spectrum (DSSS)
802.11ac/a/g/n: Orthogonal Frequency Division Multiple (OFDM)
802.11ax supports very high throughput (VHT) — HE 20/40/80 MHz
802.11ac supports very high throughput (VHT) — VHT 20/40/80 MHz
802.11n supports high throughput (HT) — HT 20/40 MHz
802.11n supports very high throughput under the 2.4GHz radio –VHT40 MHz (256-QAM)
802.11n/ac/ax packet aggregation: A-MPDU, A-SPDU
802.11b: BPSK, QPSK, CCK
802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM
802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM
802.11ax: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM
2.4GHz: 23dBm
5GHz: 25dBm
Maximum power is limited by regulatory domain
MU-MIMO allows multiple spatial streams to be allocated to different clients simultaneously on both download and upload sides.
Orthogonal frequency-division multiple access (OFDMA) allows a single transmission to be split by frequency within a channel.
Increasing signal reliability and transmitting distance.
BSS coloring marks different colors on each data which will allows client devices to stop receiving a frame and return to sleep mode as soon as they recognize these frames are not of interest to them.
The target wake time feature lets your devices to keep a radio receiver sleeping and wake it up as needed to receive periodic transmissions from an access point. The result is significant power-saving for battery-powered devices.
802.11b: 1, 2, 5.5, 11
802.11a/g: 6, 9, 12, 18, 36, 48, 54
802.11n: 6.5 to 300 (MCS0 to MCS15)
802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS=1 to 2)
802.11ax:
2.4GHz: 9 to 574 (MCS0 to MCS11, NSS=1 to 2)
5GHz: 18 to 1201 (MCS0 to MCS11, NSS=1 to 2)
Set the ACK timeout to assure the proper distance to deliver wireless signal properly
Scan signal level of an environment to provide parameters for performing Auto Transmit power and auto channel.
Automatically adjust power level
Automatically assign a clearly channel to perform RF transmission under a pervasive environment.
Collect the parameters of neighborhood Access Points to find the optimal AP.
Fast Roaming (802.11v)
Cognize the signal strength of client devices under each to steer these client devices to one of Access Points if signal level is less than the default value of AP systems.
Steer client devices to a proper frequency band for getting more band-width and speed under an Access Point.
Kick client devices that the signal (RSSI) is above the set value from the AP for reducing the interference and optimize the connecting quality.
BSSID support
Support 8 SSIDs on both 2.4GHz and 5GHz bands.
Isolate each client for avoiding an unnecessary touch, leaking sensitive data, and enhancing Internet security and reliability. The function will only available on stand-alone mode.
Independent VLAN setting can be enable or disable. Any packet that enters the Device without a VLAN tag will have a VLAN tag inserted with a PVID (Ethernet Port VID).
Broadcast VLAN-tag packets to find the destination and deliver packets over the defined path. The functions allows network topology scalable and flexible.
Integrate VLAN ID with a SSID interface to forward packets over the de-fined path. The functions isolate client devices to get more security.
Feature is enabled with specified VLAN ID, the device will only allow management access with the same specified VLAN ID from remotely location by using protocols such as telnet, SSH, snmp, syslog etc.
Controls the bottle of bandwidth to offer the limited bandwidth for an individual SSID or each client per Access Point.
Filter up to 32 sets MAC addresses per SSID
Provides a network monitoring tool for administrators to stay informed the configuration change.
Save the customized configuration as default value for different customer demands.
Perform a regular reboot on access point at assigned schedule
Perform it to enable or disable 2.4GHz or 5GHz interface from a period time.
v1/v2c/v3 support
MIB I/II, Private MIB
CLI Supported
Help operators to offload 3G to Wi-Fi seamlessly
Provide the list to display real status of wireless client devices on this Access Point.
This function will allow client devices to discover wireless Access Point under an environment and to automatically exchange data for getting authorization on accessing Internet when roaming between Access Points.
Operating: -20°C~60°C (-4°F~140°F)
Storage: -30°C~80°C (-22°F~176°F)
Operating: 0%～90% typical
Storage: 0%～90% typical
IP67
Weight: 720 g
Length: 7.48” (190 mm)
Width: 4.88”(124 mm)
Depth: 1.85(47 mm)
Subpart 15 B
Subpart C 15.247
Subpart E 15.407
EN 300 328
EN 301 893
EN 301 489
EN 50385
EN 55032
EN 55035
EN 61000
IEC 60950-1
IEC 60950-22
IEC 62368-1
EWS850AP |
Cloud6 2x2 Outdoor |
ENS620EXT |
ENH1350EXT |
|
|---|---|---|---|---|
| Model Number | ECW260 | |||
| 無線網路標準 | 802.11a/b/g/n/ac/ax | 802.11a/b/g/n/ac/ax | 802.11a/b/g/n/ac Wave 2 | 802.11a/b/g/n/ac Wave 2 |
| 無線頻段 | 2.4 GHz & 5 GHz | 2.4 GHz & 5 GHz | 2.4 GHz & 5GHz | 2.4 GHz & 5GHz |
| 2.4 GHz最大傳輸速率 | 574 Mbps | 574 Mbps | 400 Mbps | 400 Mbps |
| 5 GHz最大傳輸速率 | 1,200 Mbps | 1,200 Mbps | 867 Mbps | 867 Mbps |
| 空間串流 | 2 x 2:2 | 2 x 2:2 | 2 x 2:2 | 2 x 2:2 |
| 2.4 GHz傳輸能力 | Up to 23 dBm | Up to 23 dBm | Up to 27 dBm | Up to 23 dBm |
| 5 GHz傳輸能力 | Up to 25 dBm | Up to 25 dBm | Up to 27 dBm | Up to 23 dBm |
| 整合型天線 | - | - | - | - |
| 外接式天線 | 4 x 5 dBi | 2 x 5 dBi (2.4 GHz); 2 x 5 dBi (5 GHz) | 4 x 5 dBi | 4 x 5 dBi |
| 網路線供電標準 | 802.3af/at | 802.3af/at | 24V Proprietary | 802.3af/at |
| 有線網路連接埠 | 1 x 10/100/1000/2500 Ethernet Port | 1x 2.5GE PoE+ port | 2 x 10/100/1000 Ethernet Ports | 1 x 10/100/1000 Ethernet Port |
| 安裝方式 | Wall/Pole | Pole / Wall | Wall/Pole | Wall/Pole |
| IP防護等級 | IP67 | IP67 | IP55 | IP67 |
| 尺寸 | 190 x 124 x 47 mm | 190 x 124 x 52.5 mm | 192 x 114 x 48 mm | 174 x 111 x 30 mm |
| 網狀無線網路技術 | Yes | Yes | - | Yes |
| Cloud To-Go app | - | Yes | - | - |
| EnWiFi app | Yes | - | Yes | Yes |
|
View
|
View
|
View
|
View
|
最新的802.11ax (Wi-Fi 6) 無線基地台具備前所未有的新功能，能為中小企業的網路效益帶來大幅改善
使用ezMaster進行網路管理
