Single-Band N300 Indoor Wireless Access Point

Technical Specifications

Hardware
RF: 2.4 GHz Frequency Band
Standard: IEEE 802.11b/g/n
IEEE 802.11b/g: 2.400~2.484 GHz
Data Rate: Up to 300 Mbps
Memory: 32 MB
Flash Memory: 4 MB
Power Consumption: Up to 4W

Antenna
Internal 5 dBi Omni-Directional Antenna (diversity support)

Physical Interface
1 x RJ-45 Fast Ethernet (10/100 Mbps)
1 x Reset Button
Power Jack

LEDs Status
Power
LAN (10/100 Mbps)
WLAN (Wireless Connection)

Power Requirements
Power Supply: 90 to 240 VDC ± 10%, 50/60 Hz
Active Ethernet (Power-over-Ethernet, IEEE 802.3af)
Power Adapter (United States) 48VDC/0.375A
Device: 12V/1A

Modulations
OFDM: BPSK, QPSK, 16-QAM, 64-QAM, DBPSK, DQPSK, CCK

Operating Channels
2.4 GHz: US/Canada 1-11

Receiver Sensitivity
802.11b (2.412~2.472 GHz) best ≤ -98 dBm
802.11g (2.412~2.472 GHz) best ≤ -93 dBm
802.11n (2.412~2.472 GHz) best ≤ -93 dBm

Available Transmit Power
(Max. Power may be different depending on local regulations)
802.11b (2.412~2.472 GHz)
29 dBm @ 1~11 Mbps
802.11g (2.412~2.472 GHz)
29 dBm @ 6 Mbps
29 dBm @ 9 Mbps
28 dBm @ 12 Mbps
28 dBm @ 18 Mbps
24 dBm @ 24 Mbps
24 dBm @ 36 Mbps
23 dBm @ 48 Mbps
23 dBm @ 54 Mbps
802.11n (2.412~2.472 GHz)
26 dBm @ MCS0/MCS8
26 dBm @ MCS1/MCS9
25 dBm @ MCS2/MCS10
25 dBm @ MCS3/MCS11
24 dBm @ MCS4/MCS12
24 dBm @ MCS5/MCS13
23 dBm @ MCS6/MCS14
23 dBm @ MCS7/MCS15

Software

Topology
Infrastructure/Ad-Hoc

Operation Modes
Access Point, WDS Bridge, WDS Access Point, Universal Repeater

Multiple BSSID
Supports up to 8 BSSIDs per radio

LAN
IP (check validity and DHCP server IP range)

DHCP Server
DHCP range, lease time, client list

SSID-to-VLAN Tagging
Supports 802.1q SSID-to-VLAN tagging

Spanning Tree
Supports 802.1d Spanning Tree Protocol

Wireless
Wireless Mode: 11b/11g/11n
Channel selection (settings vary by country)
Channel bandwidth (Auto, 20 MHz, 40 MHz)
Transmission Rate:
2.4 GHz: 11n only, 11b/g/n mix, 11b only, 11b/g, 11g only

QoS
WMM (Wireless Multimedia)

VPN
Pass-Through (PPTP, L2TP, IPSec)

WPS
Software only

Management

Tx Power Control
Adjust transmit power by dBm

Configuration
Web-based configuration (http)/Telnet

Telnet Server
CLI

Firmware Upgrade
Via web browser, settings are reserved after upgrade

Administrator Setting
Administrator Username and Password Change

Reset Setting
Reboot (press 1 second).
Reset to factory default (press 10 seconds)

System Monitoring
Status Statistic and Event Log

SNMP
V1, V2c

MIB
MIB I, MIB II (RFC1213) and private MIB

Traffic Measurement
Per interface

Auto-Channel Selection
Automatically selecting least congested channel

Bandwidth Measurement
IP range and bandwidth management

Backup and Restore
Save and restore settings through Web interface

Diagnosis
IP Pinging Statistics

Wireless / Network
PPPoE: Point-to-Point Protocol over Ethernet in Client Router mode
(this function will keep trying when failed or disconnected)
PPTP: Point-to-Point Tunneling Protocol (PPTP) is a method for implementing virtual private networks

Wireless Security
WPA/WPA2 Personal (WPA-PSK using TKIP or AES)
WPA/WPA2 Enterprise (WPA-EAP using TKIP)
802.1X RADIUS Authenticator: MD5/TLS/TTLS, PEAP
SSID broadcast enable/disable
MAC Address Filtering, Up to 50 fields
L2 Isolation (Access Point mode)
Wireless STA (Client) connected list (Idle/Connection Time, Pkt statistics)

Environmental & Physical

Temperature Range
Operating: 0º to 50º C (32º to 122º F)
Storage: -20º C to 60º C (-4º F to 140º F)

Humidity (non-condensing)
Operating: 90% or less
Storage: 90% or less

Certifications
FCC
IC

Dimensions & Weights

EAP300 Device
Weight: 0.62 lbs.
Diameter: 4.73”
Height: 1.97”

Package Contents
EAP300 N300 Indoor Access Point
12V/1A Power Adapter
Ceiling Mount and Wall Screw Kit
Mounting Bracket
RJ-45 Ethernet Cable
Quick Installation Guide
CD with User Manual

Warranty
1 Year