Indoor Wireless Access Point; Dual-Band N900

Technical Specifications

Hardware
RF: 2.4 & 5 GHz Frequency Bands
Standard: IEEE 802.11a/b/g/n
Radio I: 11b/g/n: 2.412~2.484 GHz
Radio II: 11a/n: 5.18-5.24 and 5.26-5.32 and 5.5-5.7 and 5.745-5.825 GHz
Data Rate: Up to 450 Mbps in Both Frequency Bands
Memory: 64 MB
Flash Memory: 8 MB
Power Consumption: Up to 22 W

Antenna
Six (6) Internal 5 dBi Omni-Directional Antennas

Physical Interface
1 x RJ-45 Gigabit Ethernet (10/100/1000 Mbps)
1 x Reset Button
1 x Power Connector

Power Requirements
Power Supply: 90 to 240 VDC ± 10%, 50/60 Hz
Active Ethernet (Power-over-Ethernet, 802.3at)
Power Adapter (United States) 48VDC/0.375A
Device: 12V/2A

Modulations
OFDM: BPSK, QPSK, 26-OAM, 64-QAM, DBPSK, DQPSK, CCK

Operating Channels
2.4 GHz: US/Canada 1-11
5 GHz: Country dependent for the following ranges:
36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165

Software

Topology
Infrastructure/Ad-Hoc

Operation Modes
Access Point, WDS Bridge, WDS Access Point

Multiple BSSID
Supports up to 8 BSSIDs per Radio

LAN
IP (Check Validity & DHCP Server IP Range) MAC

SSID-to-VLAN Tagging
Supports 802.1q SSID-to-VLAN Tagging

Spanning Tree
Supports 802.1d Spanning Tree Protocol

Wireless
Wireless Mode: 11a/11b/11g/11n
Channel Selection (Settings Vary by Country)
Channel Bandwidth (Auto, 20 MHz, 40 MHz)
Transmission Rate:
2.4 GHz: 11n Only, 11b/b/n mix, 11b Only, 11b/g, 11g Only
5 GHz: 11n Only, 11a/n mix, 11a Only

QoS
WMM (Wireless Multimedia)

VPN
Pass-Through (PPTP, L2TP, IPSec)

WPS
Software Only

Management

Tx Power Control
Adjust Transmit Power by dBm

Configuration
Web-Based Configuration (http)/Telnet

Telnet Server
CLI

Firmware Upgrade
Via Web Browser, Settings are Reserved After Upgrade

Administrator Setting
Administrator Username & Password Change

Reset Setting
Reboot (Press 1 Second).
Reset to Factory Default (Press 10 Seconds)

System Monitoring
Status Statistic & Event Log

SNMP
V1, V2c, V3

MIB
MIB I, MIB II (RFC1213) & Private MIB

Traffic Shaping
Incoming & Outgoing Wireless Traffic Shaping

Auto-channel Selection
Automatically Selecting Least Congested Channel

Bandwidth Measurement
IP Range & Bandwidth Management

Auto Reboot
Reboot Access Point by Minute, Hour, Day, or Week

Backup and Restore
Save & Restore Settings Through Web Interface

CLI
Supports Command Line Interface

Diagnosis
IP Pinging Statistics

Log
SysLog & Local Log Support

LED Control
On/Off

AP Detection
Scanning for Available EnGenius APs

Wireless / Network
PPPoE: Point-to-Point Protocol over Ethernet in Client Router Mode
PPTP: Point-to-Point Tunneling Protocol (PPTP)

Wireless Security
WPA/WPA2 Personal (WPA-PSK Using TKIP or AES)
WPA/WPA2 Enterprise (WPA-EAP Using TKIP)
802.1X RADIUS Authenticator: MD5/TLS/TTLS, PEAP
SSID Broadcast Enable/Disable
MAC Address Filtering, Up to 50 Fields
L2 Isolation (Access Point Mode)
Wireless STA (Client) Connected List (Idle/Connection Time, Pkt Statistics)

QoS (Quality of Service)
WMM (Wireless Multimedia)

Environmental & Physical

Temperature Range
Operating: 0º C to 50º C (32º F to 122º F)
Storage: -20º C to 60º C (-4º F to 140º F)

Humidity (non-condensing)
Operating: 90% or less
Storage: 90% or less

Certifications
FCC, IC, CE

Dimensions & Weights

EAP900H Device
Weight: 0.62 lbs.
Diameter: 6.36”
Height: 1.64”

Package Contents
EAP900H Dual Band N900 Indoor Access Point
12V/2A Power Adapter
T-Rail Mounting Kit
Ceiling Mount & Wall Screw Kit
Mounting Bracket
RJ-45 Ethernet Cable
Quick Installation Guide

Warranty
1 Year